Control Units

Mainboard for GIGAcontrol A C3, automatic control board up to 2,2kW, for 400V and freq. converter operators, contacor version

Automatic control unit for sliding doors with mechanical limit switch, automatic and hold-to-run operation possible, with additional real-time clock and calendar, with LCD screen.Description:The door control unit DRICO slife 150 FU 62.3, with connection cable with CEE plug by ASO Safety is an FU automatic control unit for drives with mechanical limit switch (NES).• Output power 2,7 kW 3-phase• Protection class IP54• Integrated 3-way pushbutton OPEN-STOP-CLOSE• 24 V AUX supply• Operating modes: hold-to-run, automatic, alternating operation OPEN/STOP/CLOSE/STOP• Adjustable automatic timer-to-close

Door control unit for GfA Elektromaten drives with digital or mechanical limit switch, automatic or constant pressure to close operation, with integrated radio system, with 0,7m connection cable and CEE-plug, variant with higher power, power supply for external devices up to 1000mA (24 V DC)Description:The door control unit TS 971 by GfA Elektromaten is an automatic control panel for use with GfA Elektromaten drives with digital (DES) or mechanical (NES) limit switch system. The TS 971 control panel comes with an integrated radio receiver for 434 MHz radio products of different manufacturers. In addition the TS 971 has an integrated receiver, that can be used for the wireless transmission of the door safety edge in combination with the optional WSD module.Properties:Protection class IP54 with CEE plug or IP65 for direct wiringIntegrated push button for UP-STOP-CLOSE commandsIntegrated radio receiver for 434 MHz wireless productsParameter setting via selector switch with digital displayTwo independent, programmable relay contact, e.g. for red-green traffic-lightsOperating modes: hold-to-run mode or self-hold/ automatic modeAutomatic detection of safety edge type (Optical edge FRABA VITECTOR, resistive edge 8k2 or NC-contact type 1k2 with testing)Automatic timer-to-closeAdjustable intermediate open position, e.g. half open, venting positionAutomatic ground adjustment (only DES) to compensate for rope-stretch or subsequent change in ground heightDue to the pre-assembled, pluggable motor cable, the TS 971 can easily be connected to the drive. A faulty wiring is hereby avoided, thus minimizing installation errors and time. The connection cable can be wired into the control panel housing from either top or bottom. In addition to the motor cable, the TS 971 can work with a multitude of additional inputs, e.g. rope-switches, photo eyes, sensing edges and many more.The TS 971 by GfA Elektromaten comes with the function "radio/ wireless" already integrated, the control panel has an integrated receiver for remotes of different manufacturers using a frequency of 434 MHz. An additional radio receiver is not needed. In addition the wireless sensing edge transmission system WSD is already integrated on the control panel side. The WSD system is a wireless transmission system for sensing edges and allows monitoring and transmission of the most common sensing edge types, as well as pedestrian door and rope tension switches. The use of a coil cord is no longer needed. Of course the TS971 also allows for connection with a coil cord.The TS971 has comfort functions and allows installation in more demanding applications. For standard-applications GfA Elektromaten offers the panel type TS970.

Hormann Art. Nr. 636683, complete door control in enclosure with main switch and profile half cylinder, without power supply cable, flanges or motor cable, produced from 01.10.2003 -

Hormann Art. Nr.58203, control unit with base and power board B 971 R S6 with keyboard, production period 01.05.2016 -

Hormann Art. Nr. 636767, door control in industrial enclosure with profile half cylinder, without flange cover. Note: The 360 control unit is only compatible with the WA 300 S4 integrated controls produced from April 1st 2012 (according to index B on the type plate). Produced from April 1st 2012 -

Control Unit for dock levellers with hinged wedge lip (1-valve) with integrated door control CS310, phase sequence check by voltage monitoring, phase failure detection, release/ interlocking through door control, interlocking of start-up mechanism following a power failureDescription:Please note:This product has been discontinued by the manufacturer and is no longer available.In the "follow-up articles" tab you can find a link to the suggested replacement product.

Hormann Art. Nr. 4991962, complete door control in enclosure with main switch

Feig Electronic 3-phase frequency converter control unit for doors, supply voltage 3x200 - 480 V, for drives up to 2,2 kW (5A) with electronic or digital limit switch, with 24V (3500mA) power supply for accessories, monitored 24V brake, in large enclosure, with mains switch, includes connection cable with CEE-plugDescription:The door control unit TST FUF3-AH by FEIG Electronic is a controller with built-in frequency converter for drives with up to 2,2kW. The frequency converter allows for soft-start and -stop of the doors, resulting in reduced mechanical wear and longer product lifetime. With an increased opening speed of the door, processes can be optimized and waiting times can be reduced. The unit comes with a 24V/ 3500mA power supply for external accessoies, like radar sensors, signal lights etc. It works with digital or mechanical limit switches for door positioning. Due to the very wide range of parameter adjustments offered by all FEIG control units, the TST FUF3-AH can be programmed for many different doors functions. The parameter setting is done by using the push-buttons and full text display of the controller, no additional accessories needed! Installation of the controller is easy and the auto-setting and calibration feature of the controller simplifies it even further as it automatically sets the frequency converter parameters for soft-start and -stop.Properties:Large enclosure with built-in mains switchFrequency converter allows for variable and adjustable door speedsSoft-start and soft-stop featureFor drives up to 2,2kWwide power supply range 3~200 - 480 V ACFulfils the required standards for door controls (TüV, CE)2 integrated interfaces for sensing edges (resistive or optical systems)2 slots for optional plugin-cards, eg. 2-channel radio, 2-channel loop detector or 6-channel safety control cardProgrammable time switchDiagnostic LED on all inputsUSB-Interface for service purposesOptional I/O-extension with plugin-card (for 6 inputs, 7 outputs, time switch, 2-channel loop detector, external display, RS485- and CAN-interface)Interface for the optional module TST RFUFxCOM for parallel operation of two doorsPluggable, colour-coded connectors for all control functionsUp to 20 (+6) digital inputs and 3 (+6) relay outputs are set with standard functions as factory default

Mainboard for GIGAcontrol A R3, automatic control board up to 1,5kW, for 400V and freq. converter operators, until 2017

Hormann Art. Nr. 636702, complete door control in enclosure with profile half cylinder, without power supply cable, flanges or motor cable, produced from 01.10.2003 -

Feig Electronic 1-phase frequency converter control unit for doors, supply voltage 110 - 240 V, for drives up to 1,5 kW (10A) with electronic or digital limit switch, with 24V (500mA) power supply for accessories, in large enclosure, with mains switch, includes connection cable with CEE-plugDescription:The door control unit TST FUZ2-LGH by FEIG Electronic is a controller with built-in frequency converter for drives with up to 1,5kW. The frequency converter allows for soft-start and -stop of the doors, resulting in reduced mechanical wear and longer product lifetime. With an increased opening speed of the door, processes can be optimized and waiting times can be reduced. The unit comes with a 24V/ 500mA power supply for external accessories, like radar sensors, signal lights etc. It works with digital or mechanical limit switches for door positioning. Due to the very wide range of parameter adjustments offered by all FEIG control units, the TST FUZ2-LGH can be programmed for many different door functions. The parameter setting is done by using the push-buttons and the segment display of the controller, no additional accessories needed! Installation of the controller is easy and the auto-setting and calibration feature of the controller simplifies it even further as it automatically sets the frequency converter parameters for soft-start and -stop.Properties:Large enclosure with built-in mains switchFrequency converter allows for variable and adjustable door speedsSoft-start and soft-stop featurefor drives up to 1,5kWwide power supply range 110 - 240 V ACFulfils the required standards for door controls (TüV, CE)Integrated interface for sensing edges (resistive or optical systems)Optional plugin card for 2-channel radio system, 2-channel loop detector or 6-channel safety control cardOptional I/O-extension with plugin-card (for 6 inputs, 7 outputs, time switch, 2-channel loop detector, external display, RS485- and CAN-interface)Pluggable, colour-coded connectors for all control functionsUp to 16 digital inputs and 2 relay outputs are set with standard functions as factory default

Feig Electronic 1-phase frequency converter control unit for doors, supply voltage 110 - 240 V, for drives up to 0,75 kW (5A) with electronic or digital limit switch, with 24V (500mA) power supply for accessories, includes connection cable with CEE-plugDescription:The door control unit TST FUZ2-C by FEIG Electronic is a controller with built-in frequency converter for drives with up to 0,75kW. The frequency converter allows for soft-start and -stop oft he doors, resulting in reduced mechanical wear and longer product lifetime. With an increased opening speed oft he door, processes can be optimized and waiting times can be reduced. The unit comes with a 24V/ 500mA power supply for external accessories, like radar sensors, signal lights etc. It works with digital or mechanical limit switches for door positioning. Due to the very wide range of parameter adjustments offered by all FEIG control units, the TST FUZ2-C can be programmed for many different door functions. The parameter setting is done by using the push-buttons and the segment display of the controller, no additional accessories needed! Installation of the controller is easy and the auto-setting and calibration feature of the controller simplifies it even further as it automatically sets the frequency converter parameters for soft-start and -stop.Properties:Frequency converter allows for variable and adjustable door speedsSoft-start and soft-stop featurefor drives up to 0,75kWwide power supply range 110 - 240 V ACFulfils the required standards for door controls (TüV, CE)Integrated interface for sensing edges (resistive or optical systems)Optional plugin card for 2-channel radio system, 2-channel loop detector or 6-channel safety control cardOptional I/O-extension with plugin-card (for 6 inputs, 7 outputs, time switch, 2-channel loop detector, external display, RS485- and CAN-interface)Pluggable, colour-coded connectors for all control functionsUp to 16 digital inputs and 2 relay outputs are set with standard functions as factory default  

Hormann Art. Nr. 4981693, complete door control in enclosure with main switch, smart module and emergency stop

Door control unit for GfA Elektromaten drives with digital or mechanical limit switch, types GfA Elektromaten SI 25.15 WS / SI 45.7 WS / ST 16.24 WS, automatic or constant pressure to close operation, with integrated radio system, with 0,7m connection cable and CEE-plugDescription:The door control unit TS 971 by GfA Elektromaten is an automatic control panel for use with GfA Elektromaten drives with digital (DES) or mechanical (NES) limit switch system. The TS 971 control panel comes with an integrated radio receiver for 434 MHz radio products of different manufacturers. In addition the TS 971 has an integrated receiver, that can be used for the wireless transmission of the door safety edge in combination with the optional WSD module.Properties:Protection class IP54 with CEE plug or IP65 for direct wiringIntegrated push button for UP-STOP-CLOSE commandsIntegrated radio receiver for 434 MHz wireless productsParameter setting via selector switch with digital displayTwo independent, programmable relay contact, e.g. for red-green traffic-lightsOperating modes: hold-to-run mode or self-hold/ automatic modeAutomatic detection of safety edge type (Optical edge FRABA VITECTOR, resistive edge 8k2 or NC-contact type 1k2 with testing)Automatic timer-to-closeAdjustable intermediate open position, e.g. half open, venting positionAutomatic ground adjustment (only DES) to compensate for rope-stretch or subsequent change in ground heightDue to the pre-assembled, pluggable motor cable, the TS 971 can easily be connected to the drive. A faulty wiring is hereby avoided, thus minimizing installation errors and time. The connection cable can be wired into the control panel housing from either top or bottom. In addition to the motor cable, the TS 971 can work with a multitude of additional inputs, e.g. rope-switches, photo eyes, sensing edges and many more.The TS 971 by GfA Elektromaten comes with the function "radio/ wireless" already integrated, the control panel has an integrated receiver for remotes of different manufacturers using a frequency of 434 MHz. An additional radio receiver is not needed. In addition the wireless sensing edge transmission system WSD is already integrated on the control panel side. The WSD system is a wireless transmission system for sensing edges and allows monitoring and transmission of the most common sensing edge types, as well as pedestrian door and rope tension switches. The use of a coil cord is no longer needed. Of course the TS971 also allows for connection with a coil cord.The TS971 has comfort functions and allows installation in more demanding applications. For standard-applications GfA Elektromaten offers the panel type TS970.

Hormann Art. Nr. 636720, complete door control in enclosure, without power supply cable, flanges or motor cable, produced from 01.10.2003 -

Hormann Art. Nr. 157468, complete door control in enclosure.

Door control unit for GfA Elektromaten drives with digital or mechanical limit switch, automatic or constant pressure to close operation, with integrated radio system, in XL plastic housing, with connection kit for hardwiringDescription:The door control unit TS 971 by GfA Elektromaten is an automatic control panel for use with GfA Elektromaten drives with digital (DES) or mechanical (NES) limit switch system. The TS 971 control panel comes with an integrated radio receiver for 434 MHz radio products of different manufacturers. In addition the TS 971 has an integrated receiver, that can be used for the wireless transmission of the door safety edge in combination with the optional WSD module.Properties:Protection class IP54 with CEE plug or IP65 for direct wiringIntegrated push button for UP-STOP-CLOSE commandsIntegrated radio receiver for 434 MHz wireless productsParameter setting via selector switch with digital displayTwo independent, programmable relay contacts, e.g. for red-green traffic-lightsOperating modes: hold-to-run mode or self-hold/ automatic modeAutomatic detection of safety edge type (Optical edge FRABA VITECTOR, resistive edge 8k2 or NC-contact type 1k2 with testing)Automatic timer-to-closeAdjustable intermediate open position, e.g. half open, venting positionAutomatic ground adjustment (only DES) to compensate for rope-stretch or subsequent change in ground heightDue to the pre-assembled, pluggable motor cable, the TS 971 can easily be connected to the drive. Faulty wiring is hereby avoided, thus minimizing installation errors and time. The connection cable can be wired into the control panel housing from either top or bottom. In addition to the motor cable, the TS 971 can work with a multitude of additional inputs, e.g. rope-switches, photo eyes, sensing edges and many more.The TS 971 by GfA Elektromaten comes with the function "radio/ wireless" already integrated, the control panel has an integrated receiver for remotes of different manufacturers using a frequency of 434 MHz. An additional radio receiver is not needed. In addition the wireless sensing edge transmission system WSD is already integrated on the control panel side. The WSD system is a wireless transmission system for sensing edges and allows monitoring and transmission of the most common sensing edge types, as well as pedestrian door and rope tension switches. The use of a coil cord is no longer needed. Of course the TS971 also allows for connection with a coil cord.The TS971 has comfort functions and allows installation in more demanding applications. For standard-applications GfA Elektromaten offers the panel type TS970.

Feig Electronic 3-phase frequency converter control unit for doors, supply voltage 3x200 - 480 V, for drives up to 5,0 kW with electronic or digital limit switch, includes connection cable with CEE-plug

Hormann Art. Nr. 636715, complete door control in enclosure with main switch, profile half cylinder, and accessories bag, without power supply cable, flanges or motor cable, produced from 03.06.2010 - 28.02.2017

Control Unit for dock levellers with hinged wedge lip (1 or 2-valve), push-buttons for auto-Return, lift and mains-switch, door control with push-buttons, open-stop-close, with LC-Display

Hormann Art. Nr. 636642, complete door control in enclosure with profile half cylinder, without power supply cable, flanges or motor cable, produced from 01.10.2003 -

Replacement PCB for CS300 AWG 230V/1PH by MFZ Marantec Ovitor, for drives with digital limit switch (AWG)Description:Please note:This product has been discontinued by the manufacturer and is no longer available.In the "follow-up articles" tab you can find a link to the suggested replacement product.

Description:Please note:This product has been discontinued by the manufacturer and is no longer available.In the "follow-up articles" tab you can find a link to the suggested replacement product.