GfA Elektromaten Sectional Door Drive SE9.24 WS with Control TS971

Motor cable for GfA Elektromaten drives with digital limit switch DES, length 5m

torque support bracket for sectional door drives, GfA Elektromaten Series SG50

Door control unit TS 971 for GfA Elektromaten drives with digital or mechanical limit switch, automatic or constant pressure to close operation, with integrated radio systemDescription:The door control unit TS 971 by GfA Elektromaten is an automatic control panel for use with GfA Elektromaten drives with digital (DES) or mechanical (NES) limit switch system. The TS 971 control panel comes with an integrated radio receiver for 434 MHz radio products of different manufacturers. In addition, the TS 971 has an integrated receiver, that can be used for the wireless transmission of the door safety edge in combination with the optional WSD module.Properties:Protection class IP54 with CEE plug or IP65 for direct wiringIntegrated push button for UP-STOP-CLOSE commandsIntegrated radio receiver for 434 MHz wireless productsParameter setting via selector switch with digital displayTwo independent, programmable relay contact, e.g. for red-green traffic-lightsOperating modes: hold-to-run or self-hold/ automatic modeAutomatic detection of safety edge type (Optical edge FRABA VITECTOR, resistive edge 8k2 or NC-contact type 1k2 with testing)Automatic timer-to-closeAdjustable intermediate open position, e.g. half open, venting positionAutomatic ground adjustment (only DES) to compensate for rope-stretch or subsequent change in ground heightDue to the pre-assembled, pluggable motor cable, the TS 971 can easily be connected to the drive. A faulty wiring is hereby avoided, thus minimizing installation errors and time. The connection cable can be wired into the control panel housing from either top or bottom. In addition to the motor cable, the TS 971 can work with a multitude of additional inputs, e.g. rope-switches, photo eyes, sensing edges and many more.The TS 971 by GfA Elektromaten comes with the function "radio/ wireless" already integrated, the control panel has an integrated receiver for remotes from different manufacturers using a frequency of 434 MHz. An additional radio receiver is not needed. In addition the wireless sensing edge transmission system WSD is already integrated on the control panel side. The WSD system is a wireless transmission system for sensing edges and allows monitoring and transmission of the most common sensing edge types, as well as pedestrian door and rope tension switches. The use of a coil cord is no longer needed. Of course the TS 971 also allows for connection with a coil cord.The TS 971 has comfort functions and allows installation in more demanding applications. For standard-applications GfA Elektromaten offers the panel type TS970.

SE-ELEKTROMATEN, Drive for counter balanced sectional doors, output torque 90Nm, output speed 24 rpm, max. door weight 4000 N, hollow shaft diameter 25,4mm, supply voltage 1N~230V, with emergency hand chain for manual operation, digital limit switch DES, limit switch range E=20 revolutions max.Description:The GfA Elektromaten SE9.24 SK-DES WS sectional door drive with an output torque of 90Nm and an output speed of 24U/min is a drive for counterbalanced sectional doors. The drive can run on 230V AC.Normally installed directly on the door shaftWith digital limit switch DES, no need to reset the parameters following a power failureEmergency manual override with rapid hand chain operatorMax. door weight 4000NAC version: Supply voltage 1N~230V

Coil cord for doors, EstTPU/PP, black, cable configuration: fine-stranded 5x0,25mm²,  Lif9Y11Y, dimensions: left end = 300mm, coil length = 900mm, right end = 2000mm, max. extension length 3,5m   Description: The coil cord was developed especially for use on doors to connect the sensors and switches on the door leaf. Properties: Due to the 800mm-long spiral block, the coil cable can be extended to a length of up to 3.5m. The 5-core cable installation and a 0.25mm² conductor cross-section means the helical cable has enough strands for e.g. the safety edge and slack-rope switches Sheath and core insulation made of high-grade materials Can be installed universally on doors from various manufacturers

Electrical box with status LED, 40 x 136 x 56 mm, incl. 3x M16 cable glands, 1x M16 cable gland with bend protection and 4x M16 lock nutDescription:The Fraba Vitector large junction box is useful wherever lots of space is needed for cabling from sensors, photo-eye switches, pass-door switches, slack-rope switches, etc. The connection circuit board ensures the cables can be easily connected to the door.Further characteristics:Dimensions: 40 x 136 x 56 mmTransparent coverPre-punched cable entries 5xM16 in the housing, 1xM16 in the lidIncludes 3xM16 cable glands, 1x bend protector and 4 x locknuts

Electrical box, 90 x 48,5 x 40mm, with 1x M16 cable gland, 1x blind plug and 1x M16 cable gland with bend protectionDescription:The Fraba Vitector small junction box is distinguished by its compact design.Further characteristics:90 x 48,5 x 40mm1 x M16 open in the ground1 x pre-shaped for the ground1 x M16 open in the lidIncludes 1 x M16 cable gland, 1 blind plug, and 1 M16 with bend protection and terminal strip

Cable set for optical sensing edges OSE, includes coil cord 5x0,25 mm², cable ends 2,0m/ 0,35m, max. extension length 3,5m and IP65 junction box with connection PCB, for connection of OSE sensors (GfA Elektromaten connectors or single leads), with LED for indication of operation statusDescription:The cable set for optical sensing edges consists of:- Pluggable 5-core coil cord, straight cable ends 2,0m/ 0,35m length, can be extended to a max. length of 3,5m - IP65 junction box with connection circuit board for OSE transmitter / receiver

Cable set for optical sensing edges OSE, includes coil cord 4x0,25 mm², cable ends 2,0m/ 0,35m, max. extension length 3,5m, with junction box and connection PCBDescription:The cable set for optical sensing edges consists of:- Pluggable 4-core coil cord, straight cable ends 2,0m/ 0,35m length, can be extended to a max. length of 3,5m - pre-assembled plug for connecting to GfA Elektromaten door control units- IP65 junction box with plug-in connector for OSE transmitter / receiver as well as pass-door and slack-door switches.

Set Transmitter (Tx) and Receiver (Rx) for Optical Sensing Edge OSE, PVC-cable, cable length 6,5m/0,5m, without plugsDescription:The FRABA VITECTOR OSE-S 6501 sensor set consists of a transmitter (Tx) and a receiver (Rx) for optical sensing edges. For an electrical connection, the sensors are equipped with a top-quality PVC Cable (length: transmitter - 6.5 m and receiver - 0.5m). The sensors are based on the original FRABA OSE technology and provide the well-known OSE-signal, which is implemented in many controllers.Warning:The 4-digit sequence of numbers used on the displays shows the sensor's manufacture date in week / year format. For example, 0118 shows the sensor was produced in the first calendar week (01) of 2018.

Set Transmitter (Tx) and Receiver (Rx) for Optical Sensing Edge OSE, PVC-cable, cable length 6,5m/0,5m, with Molex-plugsDescription:The FRABA VITECTOR OSE-S 6601 sensor set consists of a transmitter (Tx) and a receiver (Rx) for optical sensing edges. For an electrical connection, the sensors are equipped with a top-quality PVC Cable (length: transmitter - 6.5 m and receiver - 0.5 m) and pre-assembled GfA plugs. The sensors are based on the original FRABA OSE technology and provide the well-known OSE-signal, which is implemented in many controllers.Warning:The 4-digit sequence of numbers used on the displays shows the sensor's manufacture date in week / year format. For example, 0118 shows the sensor was produced in the first calendar week (01) of 2018.